Obtention d’alumines α dopées polycristallines transparentes par Spark Plasma Sintering - TEL - Thèses en ligne Accéder directement au contenu
Thèse Année : 2012

Transparent polycrystalline doped α-alumina obtained by Spark Plasma Sintering

Obtention d’alumines α dopées polycristallines transparentes par Spark Plasma Sintering

Résumé

Obtaining transparent polycrystalline ceramics became an important technological challenge over the last decade. Their high mechanical (hardness, wear resistance) and physico-chemical (corrosion resistance) properties combined with a high transparency and a reasonable price could lead them to replace glasses or monocrystals as sapphire in optical applications. The main parameters to control in order to obtain highly transparent polycrystalline alpha-alumina (PCA) are the porosity size and amount as for the other transparent materials. However, as PCA is a birefringent material, the grain size also needs to be controlled. That’s why PCA should possess after sintering grains as small as possible (bigger than 0.5 µm) and a porosity closed to 0.00% with nanometric pores. This particular microstructure is usually obtained in ~ 15 hours by combining natural sintering in air with a post Hot Isostatic Pressing (HIP) treatment. In our study, the Spark Plasma Sintering (SPS) technique was used as it enables to obtain fully dense ceramics in shorter times while limiting the grain growth. First, a protocol to obtain a pure transparent PCA was established. It consists on preparing green bodies with a controlled particle’s packing before sintering. Mainly, the particle’s packing has to be macroscopically homogeneous and without agglomerates. Moreover, the pore size distribution should be the narrowest. The SPS sintering cycle was also optimised to obtain the highest optical transmission. Then, a doping protocol with grain growth inhibitors was optimised. The nature of the doping salt has a secondary effect on optical properties compared to a thermal treatment applied before sintering. Depending on the doping agent nature and/or amount, the densification temperature changes. The SPS sintering cycle has thus to be adapted. The doping agent amount has to be optimised to obtain a fine microstructure after sintering without second phase particles. Different doping agents have been compared (magnesium Mg, lanthanum La and zirconium Zr). The sample having the highest optical properties was doped with 200 cat ppm of lanthanum. Finally, an optimisation of the powder’s morphology (finer and more spherical) was performed. Moreover, the lanthanum doped alpha-alumina slurry’s preparation was optimized using centrifugation. All these processes have enabled us to obtain one of the most transparent PCA sample ever reported in the literature. It possesses an optical transmission of 68% and a grain size around 300 nm. Its mechanical properties (hardness, wear resistance) are higher than the ones of a sapphire monocrystal.
L'élaboration de céramiques polycristallines transparentes constitue un défi technologique important. Les matériaux transparents actuellement utilisés (verres ou monocristaux) possèdent des propriétés mécaniques (dureté, résistance à l'usure) et physico-chimiques (résistance à la corrosion) moins intéressantes que celles des céramiques polycristallines. Par ailleurs, le coût de production de ces dernières est inférieur à celui des monocristaux. Les deux principaux paramètres à contrôler afin d'augmenter les propriétés optiques de l'alumine alpha polycristalline sont sa porosité, comme pour tout matériau transparent, et sa taille de grains, du fait de sa biréfringence. Aussi on cherchera à obtenir après frittage un matériau possédant une très faible porosité (inférieure à 0,05%) avec une distribution fine en taille de pores centrée sur des porosités nanométriques, et une taille de grains très fine (plus grand que 0,5 µm). Actuellement, cette microstructure particulière est obtenue en ~ 15 heures en combinant un frittage naturel suivi d'un traitement par Hot Isostatic Pressing (HIP). La technique de Spark Plasma Sintering (SPS) utilisée dans cette étude permet d’obtenir des céramiques denses possédant une microstructure fine en des temps plus courts. Premièrement, un protocole d'élaboration d'une alumine pure transparente a été mis au point. Il repose sur la préparation de crus à microstructure contrôlée avant l'étape de frittage. Principalement, ils doivent présenter une distribution fine en taille de pores avec un empilement particulaire macroscopique homogène dépourvu d'agglomérats. Le cycle de frittage SPS a également été optimisé afin d'obtenir les meilleures transmissions optiques possibles. Ensuite, un protocole de dopage par des inhibiteurs de croissance de grains a été optimisé. La nature du sel dopant influe au second ordre sur les propriétés optiques des échantillons par rapport à une calcination préalable au frittage. La nature et/ou la quantité de dopant induisent un décalage plus ou moins important de la densification vers les hautes températures. Le cycle de frittage SPS doit donc être adapté en conséquence. Le taux de dopant doit être optimisé afin d'obtenir une microstructure fine après frittage sans présence de particules de seconde phase. Différents dopants ont été comparés (magnésium Mg, lanthane La et zirconium Zr) et l'échantillon possédant les meilleures propriétés optiques a été obtenu grâce à un dopage à 200 cat ppm de lanthane. Des optimisations au niveau de la morphologie des poudres (plus fines et plus sphériques) et de la préparation des suspensions d'alumine alpha dopées au lanthane (lavage par centrifugation) ont permis d'obtenir l'un des meilleurs échantillons d'alumine transparente reporté dans la littérature. Il possède une transmission optique de 68% et une taille de grains de l'ordre de 300 nm. Ses propriétés mécaniques (dureté, résistance à l'abrasion) sont supérieures à celles d'un monocristal de saphir.
Fichier principal
Vignette du fichier
these.pdf (34.38 Mo) Télécharger le fichier
Origine : Version validée par le jury (STAR)

Dates et versions

tel-00808873 , version 1 (08-04-2013)

Identifiants

  • HAL Id : tel-00808873 , version 1

Citer

Lucile Lallemant. Obtention d’alumines α dopées polycristallines transparentes par Spark Plasma Sintering. Autre. INSA de Lyon, 2012. Français. ⟨NNT : 2012ISAL0082⟩. ⟨tel-00808873⟩
382 Consultations
340 Téléchargements

Partager

Gmail Facebook X LinkedIn More