Etude des mécanismes de recristallisation de nouveaux alliages à base de Ni - TEL - Thèses en ligne Accéder directement au contenu
Thèse Année : 2014

Study of recrystallization mechanisms of new Ni based alloys

Etude des mécanismes de recristallisation de nouveaux alliages à base de Ni

Résumé

This work focuses on two grades of Ni-Cr-W alloys, one containing W precipitates (EM722) and the other not (EM721). The forged materials, provided by Aubert & Duval, had heterogeneous microstructures with very large grains. At first, a thermo-mechanical procedure was developed to obtain a reference state with a homogeneous microstructure with a small grain size and a texture relatively weak. From this reference state, the texture evolution during cold rolling (different reduction rates), was analyzed from neutron diffraction measurements and showed the strengthening of the Brass-type texture. The deformation mechanisms were studied by TEM (transmission electron microscopy) and EBSD (Electron Backscatter Diffraction) to understand the formation of this type of texture. The formation of shear bands is assumed to be the most important factor for the formation of such a texture. From the deformed states, the recrystallization kinetics was determined for two temperatures (700°C and 900°C) from micro-hardness and EBSD measurements. The recrystallization mechanisms were investigated by TEM. The SIBM (Strain Induced Grain Boundary Migration) mechanism is the predominant mechanism for the EM721 material. For the other one (EM722), which has W precipitates, the SIBM mechanism is present, but a second one (PSN: Particle Stimulated Nucleation) has also been evidenced. Furthermore, regardless of the mechanism of recrystallization, once the nuclei are formed, they twin quickly. Therefore, a further study on the evolution of twin boundaries during primary recrystallization was performed, using EBSD and especially the ASTAR system installed in a TEM. It has been shown that the twin development depends both on the grain size and the stored energy during the deformation. Finally, a Monte Carlo simulation of the primary recrystallization was also implemented. Its originality lies especially on its ability to create coherent and straight twin boundaries.
Les travaux portent sur deux nuances d’alliages Ni-Cr-W, l’une contenant des précipités de W (EM722) et l’autre non (EM721). Les matériaux forgés, fournis par Aubert & Duval, présentaient des microstructures hétérogènes avec de très gros grains. Dans un premier temps, une procédure thermomécanique a été développée afin d’obtenir un état de référence avec une microstructure homogène avec une faible taille de grains et une texture relativement peu accusée. A partir de cet état de référence, l’évolution de la texture, au cours du laminage à froid (différents taux de réduction), a été analysée par diffraction des neutrons et a montré un renforcement de la texture de type Laiton. Les mécanismes de déformation ont été étudiés en microscopie électronique en transmission et par EBSD (Electron BackScatter Diffraction) afin de comprendre la formation de ce type de texture. Les bandes de cisaillement sont supposées être un facteur important pour la formation de ce type de texture. A partir des états déformés, la cinétique de recristallisation a été déterminée pour deux températures (700°C et 900°C) à partir de mesures de microdureté et par EBSD. Les mécanismes de recristallisation ont été étudiés par MET. Le mécanisme de SIBM (Strain Induced grain Boundary Migration) est le mécanisme prépondérant pour la nuance EM721. Pour l’autre nuance, EM722, possédant des précipités de W, le mécanisme de SIBM est présent, mais en plus, un second mécanisme de PSN (Particle Stimulated Nucleation) a été mis en évidence. De plus, quel que soit le mécanisme de recristallisation, une fois que les germes sont formés, ils maclent très rapidement. Par conséquent, une étude complémentaire sur l’évolution des joints de macle pendant la recristallisation primaire a été réalisée, en employant l’EBSD et surtout le système ASTAR installé dans un MET. Il a alors été montré que cette évolution dépend à la fois de la taille des grains et de l’énergie stockée par les grains pendant la déformation. Enfin, une simulation de la recristallisation primaire de type Monte-Carlo a également été mise en œuvre. Son originalité réside notamment dans sa capacité à rendre compte de la formation des joints de macles cohérents et rectilignes.
Fichier principal
Vignette du fichier
VD2_WANG_WEI_14012014.pdf (13.11 Mo) Télécharger le fichier
Origine : Version validée par le jury (STAR)
Loading...

Dates et versions

tel-01024285 , version 1 (16-07-2014)

Identifiants

  • HAL Id : tel-01024285 , version 1

Citer

Wei Wang. Etude des mécanismes de recristallisation de nouveaux alliages à base de Ni. Autre. Université Paris Sud - Paris XI, 2014. Français. ⟨NNT : 2014PA112007⟩. ⟨tel-01024285⟩
421 Consultations
1675 Téléchargements

Partager

Gmail Facebook X LinkedIn More