Développement d'une nouvelle approche hybride pour la modélisation des échanges thermiques à l'interface outil-copeau : application à l'usinage de l'alliage d'aluminium aéronautique AA2024-T351 - TEL - Thèses en ligne Accéder directement au contenu
Thèse Année : 2012

Development of a new hybrid approach for modelling heat exchange at the tool-chip interface: application to machining aeronautical aluminium alloy AA2024-T351

Développement d'une nouvelle approche hybride pour la modélisation des échanges thermiques à l'interface outil-copeau : application à l'usinage de l'alliage d'aluminium aéronautique AA2024-T351

Résumé

This PhD. thesis is realised in the framework of an international cooperation between the University of Lorraine (France) and the University of Oujda (Morocco). The work done concerns the modelling of machining process by material removal. Two important aspects of machining have been investigated: the chip formation process and the heat exchange at the tool-chip interface. In the first part of the thesis, a FE modelling of the cutting process has been established. Chips segmentation have been particularly analysed using à new parameter (Segmentation Intensity Ratio) allowing the quantification of the phenomenon. A correlation has been established between the cutting force reduction and the chip segmentation intensity. The second part of the thesis has been devoted to the study of heat exchange at the tool-chip interface, among other phenomena that contribute to the tool wear. One important point of the study is the establishment of a hybrid identification procedure (analytical/numerical) to estimate the heat flux transmitted into the cutting tool, and identification of the heat partition coefficient at the contact interface for each cutting speed. With identified values of the heat partition coefficient obtained by varying the cutting speed, a heat exchange multi-branch law has been proposed and parameters of this law have been identified. This law corresponds firstly to the evolution of the heat partition coefficient as a function of the cutting speed. Thereafter, it was defined in term of the relative sliding velocity at the tool-chip contact interface, in order to implement it in a FE code. The user interface VUINTER of Abaqus/Explicit has been used to implement the proposed law, to fully control the mechanical and thermal contact. It is henceforth possible to implement with this user interface any thermomechanical contact (friction, heat partition coefficient, etc.). The implementation via the user subroutine VUINTER was validated first on adequate tests, then on machining. The obtained results for heat fluxes with this new procedure are in good agreement with experimental measurements for the tool-workmaterial couple considered: AA2024-T351/WC-Co
Ce travail de thèse a été réalisé dans le cadre d'une collaboration internationale entre l'Université de Lorraine (France) et l'Université d'Oujda (Maroc). Les travaux réalisés concernent la modélisation de l'usinage par enlèvement de matière. Deux aspects importants de l'usinage ont été abordés : le processus de la formation de copeaux et les échanges thermiques à l'interface outil-copeau. Dans la première partie de la thèse, une modélisation par élément finis (EF) du processus de la coupe a été mise en place. La segmentation des copeaux a été particulièrement analysée grâce à l'introduction d'un nouveau paramètre, le Rapport d'Intensité de Segmentation, permettant de quantifier ce phénomène. Une corrélation entre la réduction de l'effort de coupe et l'intensité de segmentation a été établie. La deuxième partie de la thèse a été consacrée à l'étude des échanges thermiques à l'interface outil-copeau, qui contribuent entre autres à l'usure de l'outil de coupe. Un des points importants de l'étude est la mise en place d'une procédure d'identification hybride (analytique/numérique) permettant d'estimer le flux thermique transmis dans l'outil de coupe et de remonter au coefficient de partage de la chaleur à l'interface outil-copeau pour chaque vitesse de coupe. Avec les valeurs identifiées du coefficient de partage de la chaleur pour chaque vitesse de coupe, une loi d'échange thermique multi-branches a été proposée et ses paramètres identifiés. Cette loi donnant l'évolution du coefficient de partage de la chaleur en fonction de la vitesse de coupe a également été définie en fonction de la vitesse relative de glissement à l'interface outil-copeau dans le but de l'implanter dans un code de calcul EF. L'interface utilisateur VUINTER du code Abaqus/Explicit a été exploitée pour implanter la loi proposée, afin d'appréhender complètement le contact d'un point de vue mécanique et thermique. Il est désormais possible d'implanter via cette interface-utilisateur n'importe quelle autre loi de contact thermomécanique (frottement, coefficient de partage de la chaleur, etc.). L'implantation via la subroutine VUINTER a été validée sur des cas tests d'abord, et puis ensuite en usinage. Les résultats obtenus pour les flux thermiques avec cette nouvelle procédure sont en très bon accord avec les mesures expérimentales pour le couple outil-matière considéré : AA2024-T351/WC-Co
Fichier principal
Vignette du fichier
DDOC_T_2012_0200_ATLATI.pdf (7.28 Mo) Télécharger le fichier
Origine : Fichiers produits par l'(les) auteur(s)
Loading...

Dates et versions

tel-01749259 , version 1 (29-03-2018)

Identifiants

  • HAL Id : tel-01749259 , version 1

Citer

Samir Atlati. Développement d'une nouvelle approche hybride pour la modélisation des échanges thermiques à l'interface outil-copeau : application à l'usinage de l'alliage d'aluminium aéronautique AA2024-T351. Autre. Université de Lorraine, 2012. Français. ⟨NNT : 2012LORR0200⟩. ⟨tel-01749259⟩
111 Consultations
178 Téléchargements

Partager

Gmail Facebook X LinkedIn More