Development of two techniques for thermal characterization of materials : Scanning Thermal Microscopy (SThM) and 2ω method - TEL - Thèses en ligne Accéder directement au contenu
Thèse Année : 2015

Development of two techniques for thermal characterization of materials : Scanning Thermal Microscopy (SThM) and 2ω method

Développement de deux techniques de charactérisation thermique des matériaux : La microscopie thermique à sonde locale (SThM) et la méthode 2ω

Ali Assy
  • Fonction : Auteur
  • PersonId : 771895
  • IdRef : 188482296

Résumé

Two techniques to characterize the thermal properties of materials and to analyze the heat transfer at the micro/nanoscales have been studied and are presented in this manuscript. The first technique is an Atomic Force Microscopy (AFM)-based Scanning Thermal Microscopy (SThM) technique. Operating in its active mode, the AFM probe integrates a resistive element that is electrically heated. Used in AFM contact mode, it allows the localized thermal excitation of the material to be studied. The determination of the sample thermal properties requires the analysis of the probe thermal response through the modeling of the probe-sample system including its surrounding. Through a state of the art of the SThM studies, the current scientific questions and the analytical models used to analyze the probe-sample system are exposed. Special attention is given to the probe-sample thermal interaction that conditions the tip-sample interface temperature. In this work, a new methodology based on the analysis of the dependence of force-distance curves on probe temperature obtained in ambient air has been established. It permits the study and the specification of the heat rate exchanged between probe and sample through thermal conduction through water meniscus. The methodology has been applied with samples with different thermal properties, surface roughness and wettability to three resistive probes different in size and heater configurations: Wollaston, KNT and doped silicon (DS) probes. Whatever the probe and the sample are, the contribution of water meniscus in the probe-sample interaction has been shown to be lower than the one through air. The thermal conductances at the solid-solid contact were determined for various samples. This allowed identifying the phonon transmission coefficient in the case of KNT probe and a nonmetallic sample. The heat conduction through air strongly depends on the sample thermal conductivity. Moreover, the sensitivity to sample thermal conductivity for the Wollaston and KNT probes is shown to be strongly reduced for thermal conductivities larger than 10 and few W.m-1.K-1 respectively. The second technique developed in this thesis is a less local thermal analysis method. It operates by contact, requiring the implementation of the sample with a network of resistive wire probes. One wire of the network is heated by an alternating current at frequency f and has the role of heating source, continuous and at 2f frequency, for the sample. A 2D analytical model, based on the principle of thermal-waves, was developed to identify though the measurements the effective thermal properties of anisotropic samples. Finite element simulations and this model were used to design the experimental set-up and validate the method on a sample of pure silicon. The results obtained at sample temperatures ranging from ambient to 500 K are consistent with literature.
Deux techniques de caractérisation thermique des matériaux et d’analyse du transfert de chaleur aux micro- et nano- échelles ont été étudiées et sont présentées dans ce mémoire. La première technique est la microscopie thermique à sonde locale (SThM). La pointe d’un microscope à force atomique intègre un élément résistif. Utilisée en mode contact, cette pointe, chauffée par effet joule, permet l'excitation thermique localisée de l’échantillon. La détermination des propriétés thermiques de l’échantillon nécessite l'analyse de la réponse de cette pointe avec un modèle du système sonde-échantillon et de son environnement. Un état de l'art général des études réalisées en SThM permet de poser les questions scientifiques actuellement traitées dans le domaine. Une attention particulière est accordée à l'interaction thermique sonde-échantillon. L’étude ici présentée tient compte des propriétés thermiques, de la rugosité et de la mouillabilité de la surface de différents échantillons. Une nouvelle méthodologie est établie pour la spécification du transfert de chaleur échangée par conduction thermique au travers du ménisque de l'eau formé au contact sonde-échantillon. Cette méthodologie est basée sur l'analyse de la dépendance à la température de la sonde des courbes de force-distance obtenues à l'air ambiant. Elle est appliquée à trois sondes de taille, forme et constitution différentes: la sonde Wollaston, la sonde KNT et une sonde en silicium dopé. Quels que soient la sonde et l'échantillon, la contribution du ménisque d’eau à l'interaction est montrée être inférieure à celle de l'air. La conductance thermique au contact solide-solide est déterminée pour différents échantillons. Cela a permis d’identifier le coefficient de transmission de phonons dans le cas de la sonde KNT et des échantillons non-métalliques. La conduction thermique via l’air dépend fortement de la conductivité thermique de l'échantillon. La sensibilité à la conductivité thermique pour les sondes Wollaston et KNT est part ailleurs montrée fortement réduite pour les matériaux de conductivité thermique supérieure à 10 et quelques W.m-1.K-1 respectivement. La seconde technique développée est une méthode d’analyse thermique moins locale nécessitant l’instrumentation de la surface de l’échantillon avec un réseau de sondes résistives filiformes. L’un des fils du réseau, chauffé par un courant alternatif à la fréquence f, a le rôle de source excitatrice continue et à la fréquence 2f de l’échantillon. Un modèle analytique 2D, basé sur le principe des ondes thermiques et développé pour identifier les propriétés thermiques d’échantillons anisotropes est présenté. Des simulations par éléments finis et avec ce modèle ont été utilisées pour dimensionner le montage expérimental et valider la méthode sur un échantillon de silicium pur. Les résultats obtenus à des températures de l’échantillon variant de l’ambiante à 500 K corroborent ceux de la littérature.
Fichier principal
Vignette du fichier
these.pdf (10.15 Mo) Télécharger le fichier
Origine : Version validée par le jury (STAR)
Loading...

Dates et versions

tel-01207388 , version 1 (30-09-2015)

Identifiants

  • HAL Id : tel-01207388 , version 1

Citer

Ali Assy. Development of two techniques for thermal characterization of materials : Scanning Thermal Microscopy (SThM) and 2ω method. Materials. INSA de Lyon, 2015. English. ⟨NNT : 2015ISAL0001⟩. ⟨tel-01207388⟩
464 Consultations
550 Téléchargements

Partager

Gmail Facebook X LinkedIn More